Week 10
Fri, Feb 21 CW – image of work completed in class
Today in class, I continued to work on the model of my iphone.
Fri, Feb 21 HW – image of completed homework
Wed, Feb 19 CW – image of work completed in class
Today in class, I continued with my iphone stand.
Wed, Feb 19 HW – image of completed homework
Mon, Feb 17 CW – image of work completed in class
In class, I finished the MAD Exercise #2 and started the phone stand project
Mon, Feb 17 HW – image of completed homework
For homework I started the MAD Exercise #2.
Week 9
Thur, Feb 13 CW – Image of work completed in class
In class, I printed out, sanded, and glued the pencil box challenge test.
Thur, Feb 13 HW – Image of completed homework
I already finished the hinge, so I didn’t have anything to do for homework
Tues, Feb 11 CW – Image of work completed in class
In class, I made the hinge for the next project.
Tues, Feb 11 HW – Image of completed homework
For homework, I started to work on the hinge that I was researching in class.
Week 8
Sat, Feb 8 CW – image of completed classwork
Today in class, I explored how to make a hinge in fusion without using the joint command. I started to watch some videos, but I didn’t have time to start making one.
Thur, Feb 6 CW – image of work completed in class
Today, I glued together my desktop organizer and also completed the pencil holder test. Next class I will cut it out and assemble it.
Thur, Feb 6 HW – image of completed homework
Week 7
Thur, Jan 30 CW – Image of work completed in class
Today, I printed out and assembled together the desktop organizer.
Thur, Jan 30 HW – Image of completed homework
For homework, I finished the 3d model of the desktop organizer.
Tues, Jan 28 CW – Image of work completed in class
Today I almost finished the desktop organizer. All I need to do is create the small triangles, and the I will be done with the model.
Tues, Jan 28 HW – Image of completed homework
Week 6
Fri, Jan 24 CW – image of work completed in class
Today I continued with the model of the desktop organizer
Fri, Jan 24 HW – image of completed homework
Wed, Jan 22 CW – image of work completed in class
Today, I started to model the desktop organizers by sketching and extruding both sides.
Wed, Jan 22 HW – image of completed homework
Week 5
Sat, Jan 18 CW – image of work completed in class
Sat, Jan 18 HW – image of completed homework
Thur, Jan 16 CW – image of work completed in class
Today I soldered the wires and tested if it worked. Thankfully, everything worked and the light lit up.
Thur, Jan 16 HW – image of completed homework
Tues, Jan 14 CW – image of work completed in class
Today, I connected the arm to the base and wired up the barrel jack, the led, and the switch.
Tues, Jan 14 HW – image of completed homework
Week 4
Fri, Jan 10 CW – image of work completed in class
In class, I glued together the base plate and also connected the lower and upper arm with screws.
Fri, Jan 10 HW – image of completed homework
For homework, I completed the base of the lamp. In class tomorrow, I will cut out the base and try to connect the pieces that I have to create the lamp.
Wed, Jan 8 -CW – image of work completed in class
Today I put the magnets and the plates on the lower arm and glued it together.
Wed, Jan 8 HW – image of completed homework
For homework, I completed modeling the base and the base verticals, so all I need to do is connect the base to the lamp. I will do this in class when I get back and also glue the upper arm together.
Week3
Thur, Dec 19 CWW – image of completed classwork
I cut out my upper arm parts again, this time with the correct spacing. I didn’t have time to glue it, so I will do that when I get back from break.
Thur, Dec 19 HW – None
Wed, Dec 18 CW – image of work completed in class
In class, I glued together the upper arm and magnets and also cut out the parts for the upper arm. Unfortunately, the holes on the upper arm were too close to the edge, so I have to print it again on Thursday.
Wed, Dec 18 HW – image of completed homework
For homework, I worked on the holes in the lower arm horizontal.
Mon, Dec 16 CW – image of work completed in class
In class, I extruded the lower arm and connected the lower and upper arms with joints. I also created the connector between the lower arms. Also, I sanded down my laser-cut parts for the upper arm and made them cleaner.
Mon, Dec 16 HW – image of completed homework
For homework, I created the lower arm sketch and the two metal disks that will be in the final design. This was similar to the upper arm, except different dimensions and not yet making the joint and extrusion of the lower arm.
Week 2
Thur, Dec 12 CW – Image of work completed in class
Thur, Dec 12 HW – Image of completed homework
Tues, Dec 10 CW – Image of work completed in class
Tues, Dec 10 HW – Image of completed homework
Week 1
Fri, Dec 6 CW – image of completed classwork
We created a box with a lid, and learned two different ways to make a hole in a shape. One was the hole command, and the other was to create a sketch and extrude into the object so that it cuts out the shape.
Wed, Dec 4 CW – image of completed classwork
Started to learn fusion, most important part is that every part of the completed object needs to be a different component.
