Week 10
Fri, Feb 21 CW – image of work completed in class
I used the joint command to put one inside connected to the outside wall but relized my second one was to small so I re extruded it to make sure it would fit for the perfect mesurements so once the printers are fixed it will fit together smoothly.
Fri, Feb 21 HW – image of completed homework
For home work I made a new component and then made a new sketch for the bottom took the mesurements and made the bottom I then extruded it .125 and used the joint tool to connect it to the wall of the pencil box.
Wed, Feb 19 CW – image of work completed in class
I made these two pieces by making one but i extruded each of them differently for the the one spot thats open because when jointing them the only way for then to be even is if they are flipped by the must be extruded differently.
Wed, Feb 19 HW – image of completed homework
I made a whole new component and then where i put the positvies on y first one i put negatives there instead and did it all on one new sketch.
Mon, Feb 17 CW – image of work completed in class
i glued all my parts together adn then used many large clamps to keep all my parts together and stop them from falling apart and ruining the procces of the wood glue
Mon, Feb 17 HW – image of completed homework
Week 9
Thur, Feb 13 CW – Image of work completed in class\
I relizsed that these parts were not correct and fixed them by making the middle and the bottoms holes so the will fit easier and the procced will be easier.
Thur, Feb 13 HW – Image of completed homework
Tues, Feb 11 CW – Image of work completed in class
i made the small ttriangles bye exdruding one of them then copy and pasting them then i used the joint tool to make sure the were evenly split then i combined them.
Tues, Feb 11 HW – Image of completed homework
I made 3 peaices by making the first one the copy and pasting it then i made three more.
Week 8
Sat, Feb 8 HW – image of completed homework
I used the same video as the large vertical to create one small vertical except i extruded a smaller part and set the distance between the two also a lot smaller it was a challenge but i was able to over come it during the extrusion parts.
Thur, Feb 6 CW – image of work completed in class
made my front vertical and my triangles.
Thur, Feb 6 HW – image of completed homework
Week 7
Thur, Jan 30 CW – Image of work completed in class
fusion had some trouble today but I got my large triangle done and got my back part done
Thur, Jan 30 HW – Image of completed homework
had trouble extruding bottom but was finnaly able to do so.
Tues, Jan 28 CW – Image of work completed in class
Finshed the bottom and the back
Tues, Jan 28 HW – Image of completed homework
Week 6
Fri, Jan 24 CW – image of work completed in class
made front side and sepreated the two sides with a joint
Fri, Jan 24 HW – image of completed homework
none
Wed, Jan 22 CW – image of work completed in class
made left and right side.
Wed, Jan 22 HW – image of completed homework\
none
Week 5
Sat, Jan 18 CW – image of work completed in class
Printed out the lower arms and horizantal and glued magnets
Your postings should discuss each step in the design process in detail and provide examples. – 65%
Sat, Jan 18 HW – image of completed homework
No Home work
Thur, Jan 16 CW – image of work completed in class
Redid the lower arm side to fit for the joints
Your postings should discuss each step in the design process in detail and provide examples. – 65%
Thur, Jan 16 HW – image of completed homework
No homework
Tues, Jan 14 CW – image of work completed in class
made my lower arm horizantal after messing up the joint
Your postings should discuss each step in the design process in detail and provide examples. – 65%
Tues, Jan 14 HW – image of completed homework
No homework
Week 4
Fri, Jan 10 CW – image of work completed in class
printed base verticals
Fri, Jan 10 HW – image of completed homework
connected Base Verts
Wed, Jan 8 -CW – image of work completed in class
Wed, Jan 8 HW – image of completed homework
i lazer cutted the lower parts and made my base disc
Week3
Thur, Dec 19 CWW – image of completed homework
Thur, Dec 19 HW – None
Wed, Dec 18 CW – image of work completed in class
Wed, Dec 18 HW – image of completed homework
Mon, Dec 16 CW – image of work completed in class
Mon, Dec 16 HW – image of completed homework
Week 2
Thur, Dec 12 CW – Image of work completed in class
Thur, Dec 12 HW – Image of completed homework
Tues, Dec 10 CW – Image of work completed in class
Tues, Dec 10 HW – Image of completed homework
Week 1
Fri, Dec 6 CW – image of completed homework
Starting to learn fusion. Also knowing that every single part has to have a different component.
i learned how to make a hole and how to put a top on the box.
saved sketch ready to use laser to cut was unable to do homework because I had not fineshed lazer cutting yet.
fineshed lower arms and printed out and sanded the first part.
homework for 1/8/2025