2/25 cw
almost finished orthographic drawing of phone
Week 10
Everything done! (lamp is further down on the page)
Fri, Feb 21 CW – image of work completed in class]
started phone blueprint
Fri, Feb 21 HW – image of completed homework
Wed, Feb 19 CW – image of work completed in class
finished gluing box and desktop organizer.
Wed, Feb 19 HW – image of completed homework
can’t do any hw because waiting to glue stuff
Mon, Feb 17 CW – image of work completed in class
printed all parts of box test; dry assembled
also fully dry assembled and taped desktop organizer
Mon, Feb 17 HW – image of completed homework
couldn’t do any hw since waiting to print
Week 9
Thur, Feb 13 CW – Image of work completed in class
finished box fusion design. began saving dxf files, saved everything other than the bottom
Thur, Feb 13 HW – Image of completed homework
finished front side and left side of box test.
Tues, Feb 11 CW – Image of work completed in class
dry assembled desktop organizer. started box test.
Tues, Feb 11 HW – Image of completed homework
couldn’t do any hw – have to finish glueing all parts
Week 8
Sat, Feb 8 CW – image of completed homework
Printed (Or in the picture, printing) all parts. had some fusion issues with jointing the front, back, and bottom together so had to fix that as well.
Thur, Feb 6 CW – image of work completed in class
printed back vert, small triangles, and bottom
Week 7
Thur, Jan 30 CW – Image of work completed in class
finished design. small traingles, and front vertical done.
Thur, Jan 30 HW – Image of completed homework
started the front vertical but noticed that large triangle part was on the wrong side. worked on it for a while but couldn’t figure it out, so I’ll ask how to fix this in class tomorrow.
Tues, Jan 28 CW – Image of work completed in class
Created back side, back vertical, bottom, and the large triangle part. jointed all.
Tues, Jan 28 HW – Image of completed homework
Week 6
Fri, Jan 24 CW – image of work completed in class
finished both the right and left side and jointed them. also finished front sketch
Fri, Jan 24 HW – image of completed homework
Wed, Jan 22 CW – image of work completed in class
finished sketch and extrusion of left & right hand side
Wed, Jan 22 HW – image of completed homework
finished lamp. glued lower arm, put in screws and standoffs, wired + soldered, put together baseplate, and turned on the lamp!
Week 5
Sat, Jan 18 CW – image of work completed in class
glued small metal plates onto upper arm
Sat, Jan 18 HW – image of completed homework
finished printing all parts (new verts, baseplate, and lower horiz) and glued large metal plates onto the verticals
Thur, Jan 16 CW – image of work completed in class
finished design on fusion and completed base sanding and switch
Thur, Jan 16 HW – image of completed homework
Tues, Jan 14 CW – image of work completed in class
found a huge error with the joint command on the small metal plate. sanded my lower arm and then realized I have to reprint both my base plate and my lower arm horizontal, meaning I have to remodel them from the start. I made a new joint with the lower arm and the upper arm and began to extrude the horizontal lower arm.
Tues, Jan 14 HW – image of completed homework
Week 4
Fri, Jan 10 CW – image of work completed in class
finished printing lower arm and base plate.
Fri, Jan 10 HW – image of completed homework
finished modelling base, base plate, and bottom plate.
Wed, Jan 8 -CW – image of work completed in class
finished base and base verticals, just have to “model the base” next class, then will be good to print!
Wed, Jan 8 HW – image of completed homework
continued holes in lower horiz arm
Week3
Thur, Dec 19 CWW – image of completed homework
started holes in the lower horizontal arm
Thur, Dec 19 HW – None
Wed, Dec 18 CW – image of work completed in class
finished lower horizontal arm by extrusion
Glued upper arm
Wed, Dec 18 HW – image of completed homework
started lower horizontal arm
Mon, Dec 16 CW – image of work completed in class
printed upper arm on wood, sanded it down & taped together… extruded lower arm and started construction
Mon, Dec 16 HW – image of completed homework
started lower arm and created small disks (large and small)
Week 2
Thur, Dec 12 CW – Image of work completed in class
learned how to use lazer cutter and converted drawings into dxf files… gonna cut the parts next class !
Thur, Dec 12 HW – Image of completed homework
cut into the upper arms using the horizontal upper arm and learned to use combine/cut features
Tues, Dec 10 CW – Image of work completed in class
started the second upper arm and started joinery
Tues, Dec 10 HW – Image of completed homework
started initial drawing for upper side arm; learned tangent, constraint, and other functions.
Week 1
Fri, Dec 6 CW – image of completed homework
Started box 2 and learned to extrude holes & add a lid
Wed, Dec 4 CW – image of work completed in class
Started to learn Fusion and that every part needs to be a separate component
